trioprices.blogg.se - Wanderer solar charge controller

#Wanderer solar charge controller manuals
#Wanderer solar charge controller install
#Wanderer solar charge controller Bluetooth

Required to be controlled by specified voltage regulation set points for Absorption, Float, and Equalization charging stages. For the most accurate retum of capacity, and for the prevention of excessive gassing pressure, the battery is Battery charging is a current-based process so controlling the current will control the battery voltage. The Wanderer utilizes Pulse Width Modulation (PWM) technology for battery charging. Charges over-discharged lithium-ion batteries.Integrated communication port for remote monitoring.Integrated 5V 2A USB ports for extra charging.Backlit LCD screen for displaying system operation, diverse load control and error codes.Protection against: overcharging, over current, short-circuit,reverse current and reverse polarity.

Temperature compensation and correcting the charging and discharging parameters automatically, improving battery lifetime.

Deep Cycle Sealed, Gel and Flooded battery options.

Automatically detects 12V or 24V DC system voltages, 10A Charging Capacity.

The controller is embedded with self-diagnostics and electronic protection functions that prevent damages from installation mistakes or system faults. It can be used for 12V/24V battery banks. Integrating highly efficient PWM charging, this controller increases battery life and improves system performance. The Wanderer is an advanced charge controller for off-grid solar applications.

#Wanderer solar charge controller manuals

Solar panels to the charge controller until the battery is connected.ġ1.1 Related Manuals / Resources General Information

Do NOT equalize VRLA type AGM / GEL / LITHIUM batteries UNLESS permitted by battery manufacturer.Ĭonnect battery terminals to the charge controller BEFORE connecting the solar panel (s) to the charge controller.

Equalization is carried out only for non-sealed / vented / flooded/ wet cell lead-acid batteries.

Please carefully review the specific requirements of the battery used in the system.

Too high of an equalizing charge or too long of one may cause damage.

Over-charging and excessive gas precipitation may damage the battery plates and activate material shedding on them.

Wear eye protection and have fresh water available in case there is contact with the battery acid.

Be careful when working with large lead-acid batteries.

Be certain there is enough ventilation to release the gases.

Explosive battery gases may be present while charging.

Use only sealed lead-acid, flooded, gel or lithium batteries which must be deep cycle.

Do NOT let the positive (+) and negative (-) terminals of the battery touch each other.

Do NOT allow water to enter the controller.

The charge controller should be installed indoors in a well-ventilated, cool, and dry environment.

Use the Open Circuit (Voc) to make sure the voltage does not exceed this value when connecting panels together in series.

Ensure input voltage does not exceed 50 VDC to prevent permanent damage.

This may cause a dangerous occurrence where the controller would experience a high open-circuit voltage at the terminals.

NEVER connect the solar panel array to the controller without a battery.

#Wanderer solar charge controller Bluetooth

Integrated RS232 port allows communication with BT-1 Bluetooth module and usage of Renogy BT smartphone app.Capable of charging over-discharged lithium batteries.

#Wanderer solar charge controller install

Compact in size makes it easy to install virtually anywhere.Integrated 5V 2A USB ports to charge USB devices.Backlit LCD screen for displaying system operation, diverse load control and error codes.Intelligent protection against reverse polarity, overcharging, short-circuit, and reverse current. Smart 4 Stage PWM charging (Bulk, Boost, Float, and Equalization).Optimized for a 12V/24V system Deep cycle Sealed (AGM), Gel, Flooded and Lithium battery option ready.If you have any questions regarding this product, please submit a case ! Key Features The controller comes equipped with fully comprehensive self-diagnostics and electronic protection functions to prevent damage from installation mistakes or system faults. The compact size of the controller makes installation a breeze. This advanced charge controller is designed for off-grid solar applications and can be used with a 12V/24V battery or battery bank. Designed with a simple interface for ease of use the controller uses an LCD to notify users of battery information. The Renogy Wanderer 10A solar charge controller integrates efficient PWM charging to increase battery life and improve system performance.